承德市萬吉儀器儀表制造有限公司
Chengde Wanji instrument and Meter Manufacturing Co., Ltd.
展商會員第 4 年   展臺號:PY14386   參觀人數:9607
  • 公司資質:已認證
友情鏈接
拉伸沖擊是試驗機 拉伸沖擊檢測 生產廠家
放大圖片
 
產品型號: XJL
原產地: 承德市萬吉儀器儀表制造有限公司
價格:
新品注意:上市時間是 2016-1 !!
收藏產品 索取資料 咨詢價格
創新點
  自動顯示沖擊強度 自動換算 質量好
 
產品簡介       技術參數       主要特點
XJL指針拉伸沖擊試驗機
                        

一 產品介紹
   主要用于在規定的拉伸沖擊速度下,測定塑料試樣斷裂所需能量的測試。 用于測定塑料等非金屬材料的脆性、韌性。
二 符合標準:
GB/T 13525-92《塑料拉伸沖擊性能試驗方法》
ASTM D1822-2006《使塑料及電絕緣材料斷裂所需的拉伸沖擊能量的測試方法》
ISO 8256-2004《塑料-拉伸-沖擊強度的測定》
三 技術參數:
1沖擊速度:3.8m/s
2沖擊能量:15J 25J
3擺錘力矩:pd15J=8.03848Nm pd25J=13.39746Nm
4擺錘預揚角:160°
5打擊中心距:395mm
6使用溫度:(15-35)℃
7試樣尺寸:長度80±2mm 寬度15±0.5mm 厚度<4mm
8 夾具間的自由長度:30±2mm 
9 電源: 220VAC-15%~220VAC+10% 50HZ (單相三線制)
10試樣形狀和尺寸:試樣厚度優先選用1mm。由產品裁取的試樣,保留原厚度;厚度大于4mm的試樣應機械加工為4mm。對于很薄的薄膜,可以使用多層試樣,但應重疊良好。
11選擇合適的擺錘使沖擊能量讀數在試驗機有效范圍內,參照下表:
(在能夾緊試樣的前提下盡量選擇質量小的丁字頭)
擺錘沖擊能量J 丁字頭質量g
15.0
25.0 30±1或60±1
60±1或120±1

擺錘沖擊能量J

丁字頭質量g

15.0

25.0

30±1或60±1

60±1或120±1



  XJL數顯拉伸沖擊試驗機
                        

一 產品介紹
   主要用于在規定的拉伸沖擊速度下,測定塑料試樣斷裂所需能量的測試。 用于測定塑料等非金屬材料的脆性、韌性。
二、特點
 1 采用圓光柵測角技術,具有精度高、穩定性好和測量范圍大等特點
 2 具有數字化測量計算沖斷功、沖擊強度、計算一批試樣的平均值等功能
 3 預仰角、 升角校驗方便
 4 顯示方式:液晶

三符合標準:
GB/T 13525-92《塑料拉伸沖擊性能試驗方法》
ASTM D1822-2006《使塑料及電絕緣材料斷裂所需的拉伸沖擊能量的測試方法》
ISO 8256-2004《塑料-拉伸-沖擊強度的測定》
四技術參數:
1沖擊速度:3.8m/s
2沖擊能量:15J 25J
3擺錘力矩:pd15J=8.03848Nm pd25J=13.39746Nm
4擺錘預揚角:160°
5打擊中心距:395mm
6使用溫度:(15-35)℃
7試樣尺寸:長度80±2mm 寬度15±0.5mm 厚度<4mm
8 夾具間的自由長度:30±2mm 
9 電源: 220VAC-15%~220VAC+10% 50HZ (單相三線制)
10試樣形狀和尺寸:試樣厚度優先選用1mm。由產品裁取的試樣,保留原厚度;厚度大于4mm的試樣應機械加工為4mm。對于很薄的薄膜,可以使用多層試樣,但應重疊良好。
11選擇合適的擺錘使沖擊能量讀數在試驗機有效范圍內,參照下表:
(在能夾緊試樣的前提下盡量選擇質量小的丁字頭)
擺錘沖擊能量J 丁字頭質量g
15.0
25.0 30±1或60±1
60±1或120±1

擺錘沖擊能量J

丁字頭質量g

15.0

25.0

30±1或60±1

60±1或120±1


XJL pointer tensile impact tester
Introduction of a product
It is mainly used for testing the energy required for fracture of plastic specimens under specified tensile impact velocity. It is used to determine brittleness and toughness of nonmetallic materials such as plastics.
Two meet the criteria:
GB/T 13525-92 "test method for tensile impact properties of plastics"
ASTM D1822-2006 "test method for tensile impact energy required for fracture of plastics and electrical insulating materials"
ISO 8256-2004 "plastics tensile determination of impact strength"
Three technical parameters:
1 impact speed: 3.8m/s
2 impact energy: 15J 25J
3 pendulum torque: pd15J=8.03848Nm pd25J=13.39746Nm
4 pendulum preheating angle: 160 degrees.
5 strike center distance: 395mm
6 use temperature: (15-35) C
7 sample size: length 80 + 2mm width 15 + 0.5mm thickness <4mm
8 free length of fixture: 30 + 2mm
9 power supply: 220VAC-15% to 220VAC+10% 50HZ (single phase three wire system)
10 sample shape and size: 1mm is preferred for specimen thickness. The sample cut from the product should be kept at the original thickness; the specimen with a thickness greater than 4mm should be machined to 4mm. For thin films, multi-layer specimens can be used but should overlap well.
11 select the appropriate pendulum to make the impact energy reading in the effective range of the tester.
(try to choose a small T-shaped head on the premise of clamping the sample).
Pendulum impact energy J T-head quality G
Fifteen
25.030 + 1 or 60 + 1
60 + 1 or 120 + 1
XJL digital tensile impact tester
Introduction of a product
It is mainly used for testing the energy required for fracture of plastic specimens under specified tensile impact velocity. It is used to determine brittleness and toughness of nonmetallic materials such as plastics.
Two. Characteristics
1 the circular grating angle measurement technology has the characteristics of high accuracy, good stability and wide measuring range.
2, it has the functions of digital measurement and calculation, such as punching work, impact strength and calculating the average value of a batch of samples.
3 pre elevation angle and elevation angle check convenience.
4 display mode: LCD
Three meet the criteria:
GB/T 13525-92 "test method for tensile impact properties of plastics"
ASTM D1822-2006 "test method for tensile impact energy required for fracture of plastics and electrical insulating materials"
ISO 8256-2004 "plastics tensile determination of impact strength"
Four technical parameters:
1 impact speed: 3.8m/s
2 impact energy: 15J 25J
3 pendulum torque: pd15J=8.03848Nm pd25J=13.39746Nm
4 pendulum preheating angle: 160 degrees.
5 strike center distance: 395mm
6 use temperature: (15-35) C
7 sample size: length 80 + 2mm width 15 + 0.5mm thickness <4mm
8 free length of fixture: 30 + 2mm
9 power supply: 220VAC-15% to 220VAC+10% 50HZ (single phase three wire system)
10 sample shape and size: 1mm is preferred for specimen thickness. The sample cut from the product should be kept at the original thickness; the specimen with a thickness greater than 4mm should be machined to 4mm. For thin films, multi-layer specimens can be used but should overlap well.
11 select the appropriate pendulum to make the impact energy reading in the effective range of the tester.
(try to choose a small T-shaped head on the premise of clamping the sample).
Pendulum impact energy J T-head quality G
Fifteen
25.030 + 1 or 60 + 1
60 + 1 or 120 + 1

澳洲幸运8开奖数结果